Search Results for: cd50

Does CUTEK® ECO have the same properties as CUTEK® Extreme CD50?

Like CUTEK® Extreme CD50, CUTEK® ECO penetrates deeply into the timber to minimise splitting, cupping, and warping. It also stays permanently mobile inside the timber to repel and displace moisture. With each additional coat of CUTEK® ECO, this protection increases.

Does CUTEK® Quickclean cure mould?

No. CUTEK® Quickclean will remove mould and fungal growth on the surface of the timber however it does not cure the timber from mould reappearing on the timber.

To protect timber against mould and fungal decay, apply CUTEK® Extreme CD50 to your timber. CUTEK® Extreme CD50 coated wood resists damage caused by fungal decay, mould, termites and rot while repelling moisture to improve dimensional stability and minimise cupping, warping and splitting.

Garage Doors

If the wood being coated is on a garage door and the glue holding the wood to the frame is a rubber-based adhesive (or you are uncertain), run a bead of glazing sealer along the back of the door where the wood meets the frame. This will ensure the wood remains intact if CUTEK® Extreme CD50 comes in contact with the adhesive.

Glazing

CUTEK® products have been successfully used on wooden joinery for decades. It is important to note that many silicones and rubber-based sealants have poor oil and solvent resistance, and are incompatible with CUTEK® Extreme CD50. We recommend polyurethane or flouro-silicone technology as a starting point for sealant evaluation for use with CUTEK® Extreme CD50. At all times, careful testing of glues and sealants used in joinery manufacture should be undertaken to ensure compatibility with CUTEK® Extreme CD50 prior to use. Some manufacturers in the past have achieved good adhesion by applying a polyurethane sealer prior to applying adhesives/sealant on CUTEK® Oil coated surfaces. Applying after the CUTEK® Oil has completely cured (dry and non-greasy) is the best practice. Please contact us for and project advice.

 

 

How do I apply CUTEK® Extreme CD50?

STEP 1: Prepare

Before using CUTEK® oil, ensure the wood to be coated is clean, non-greasy and dry (moisture content must be less than 17%). You must appropriately prepare your timber BEFORE applying CUTEK® oil. It is also very important that the surface of the wood is free from chemical residues and is not exposed to environmental contaminants such as dusts while CUTEK® oil is drying.

If you have… NEW TIMBER:

Your timber must be bare, clean and dry before applying CUTEK® oil. If your timber presents with surface contaminants such as stains caused by water, iron or tannins, or chemical residues, we recommend using CUTEK® Restore prior to application of CUTEK® oil.

If you have… OLD, GREYED OR WEATHERED UNCOATED WOOD:

Old, dirty, stained or grey weathered timber should be prepared and restored by first applying CUTEK® Restore which will remove the grey and reinstate the original natural colour, grain and beauty of your wood prior to application of CUTEK® oils.

If you have… WOOD PREVIOUSLY COATED WITH A NON-CUTEK® COATING:

CUTEK® oils must be applied to bare, clean and dry wood. This allows the CUTEK® oil to freely penetrate/diffuse into your timber. Wood previously coated with a film forming product such as stains, linseed oil, paint, polyurethane, water-based oils, etc. can inhibit this penetration/diffusion and must be removed first with CUTEK® Wood Stripper and CUTEK® Restore prior to the application of CUTEK® oil. In some circumstances complete removal of previous coatings by machine sanding/abrasion can also be a suitable preparation method.

If you have… WOOD PREVIOUSLY COATED IN CUTEK® EXTREME CD50:

Prepare for a maintenance recoat of CUTEK® oil by using CUTEK® Quickclean to remove grease, grime and other dirt from your timber. If maintenance has been neglected for a long period of time and the timber has either greyed, become heavily stained by tannins or iron, or if there is an excessive build-up of CUTEK® Colourtone, use CUTEK® Restore to refresh your timber prior to recoating.

STEP 2: Protect

BEFORE YOU PROTECT: After preparing your timber, it will need to be completely dry prior to coating with CUTEK® oil. It is very important that your timber is clean, non-greasy and dry with a moisture content of less than 17%. It is also very important that the surface of the wood is free from chemical residues and is not exposed to environmental contaminants such as dusts while CUTEK® oil is drying.

WEATHER: Once applied, CUTEK® oil generally requires 2-3 days of dry conditions after coating to facilitate full penetration/diffusion and an even colour finish; so check your weather forecast before coating.

COLOURTONE: Clear, un-tinted CUTEK® oil will allow your wood to naturally lighten/silver/grey when exposed to sunlight while retaining its protection characteristics. Unless you want a clear finish that will naturally lighten/silver/grey off in a few months, it is important to mix in 1 CUTEK® Colourtone to this can of oil before use.

APPLICATION: Stir the CUTEK® Oil oil thoroughly (with the added CUTEK® Colourtone if desired) before and during use. Make sure you stir from the bottom of the can to ensure active ingredients are properly mixed throughout the oil. Apply thin, even coats with a brush, paint pad or lambswool applicator. CUTEK®’s DeckBoss brush is a good option. TIP: CUTEK® oil works best when applied as a THIN COAT – two or three thin coats on finished wood and hardwoods are much better than one or two thick coats. For best results, ONE coat of CUTEK® oil should be applied to all faces of the wood prior to installing, and apply a SECOND coat once the first coat has completely penetrated/diffused.

DRYING TIME: Unlike traditional wood coatings, CUTEK® oil needs to penetrate/diffuse deeply into your timber. After coating, CUTEK® oil will slowly migrate into your wood to repel and displace moisture, improve dimensional stability and lengthen the service life of your timber.

This penetration/diffusion process varies in time for many reasons including differences in timber type (species, density, porosity, age of timber and residual moisture content) as well as environmental factors (temperature, humidity, weather). Sometimes this drying process can take several days to complete. You will know when your timber is ready for a recoat of CUTEK® oil when it is completely dry and non-greasy. Please note the second coat of CUTEK® oil will take longer to migrate into your timber than the first coat.

CLEAN-UP: Equipment (including brushes) may be cleaned with turps or soap and water. If not correctly cleaned or disposed of, oily rags and other oily materials may cause combustion fires. After use you MUST immediately spread out all oily material outside to dry, by flattening them out to their full size in an airy spot at temperatures above 4 degrees Celsius, or wash them thoroughly with water and detergent and rinse. Remove all oil from all clothes, tools, rags and any other materials contacted during use or as a result of an accidental spill. Ensure wash water is disposed in accordance with local regulations.

MAINTENANCE: With CUTEK®, maintenance is simple, fast, and cost effective. CUTEK® oil will not crack, peel or split, and your wood can be easily rejuvenated or restored using our Prepare and Protect system – no need to sand or strip. CUTEK® oil should be reapplied when the wood is no longer beading water, or as frequently as necessary to retain the natural beauty and colour of the wood. Typically, horizontal exterior wood surfaces exposed to full weather such as pool decks and handrails will require re-coating more frequently (initially after 6 months, then annually), while other surfaces such as vertical rough-sawn cladding will need recoating less often.

How long can I store CUTEK® Extreme CD50 for?

CUTEK® Extreme CD50 can be stored for one year or more and reused for the next coating season, when stored correctly. To store correctly, store in a cool, dry area out of direct sunlight; lid must be airtight. If the lid has been damaged, the remaining contents may be tipped into another compatible container (HDPE or Lined metal containers). Minimising the air space in the can will also increase the storage life of the product.

If the oil has been tinted with a CUTEK® Colourtone, the colour may settle out and be difficult to stir in again if some time has passed. Use caution when mixing new and old CUTEK® Oils that have been coloured with a CUTEK® Colourtone; there may be some discrepancies in colour due to storage.

How long does it take for CUTEK® Extreme CD50 to dry?

Unlike traditional wood coatings, CUTEK® oil needs to penetrate/diffuse deeply into your timber. After coating, CUTEK® oil will slowly migrate into your wood to repel and displace moisture, improve dimensional stability and lengthen the service life of your timber. This penetration/diffusion process varies in time for many reasons including differences in timber type (species, density, porosity, age of timber and residual moisture content) as well as environmental factors (temperature, humidity, weather). Sometimes this drying process can take several days to complete. You will know when your timber is ready for a recoat of CUTEK® oil when it is completely dry and non-greasy. Please note the second coat of CUTEK® oil will take longer to migrate into your timber than the first coat.

How long will CUTEK® timber oil last? How often will I have to reapply?

CUTEK® timber oils should be reapplied when the wood is no longer beading or as frequently as necessary to retain the natural or altered colour of the wood. Timing will differ depending on many variables including the age and porosity of the wood, species, situation, design, aspect, weathered exposure and adequacy of preparation.

When considering frequency of maintenance there are two factors to consider:

  1. Protection: CUTEK® Extreme CD50 diffuse deeply into wood to provide, long-term, accumulative, inside out protection. Even when the timber surface has greyed and weathered, CUTEK® timber oils remain permanently mobile in the timber, meaning protection is not compromised even if the outward appearance of the wood has changed. Each additional coat of CUTEK® timber oil provides further additional protection against moisture.
  2. Appearance: To maintain the natural colour of freshly oiled wood for longer or alter the appearance of your timber, a CUTEK® oil with an added CUTEK® Colourtone should be applied. Over time and with exposure to sunlight and UV, the colour will slowly fade to a silver patina. Colour durability and the rate at which this fading occurs is dependent on many factors such as age and porosity of the wood, species, situation, design, aspect, and degree of exposure to the weather. CUTEK® timber oil should be reapplied as frequently as necessary to maintain desired colour vibrancy.

I have just applied CUTEK® Extreme CD50 oil and it is taking a long time to dry. Why is this?

CUTEK® oils work by deeply diffusing into the wood and they won’t dry on the surface until this process has been fully completed. The drying process varies in time according to many different factors such as density, porosity, species, residual moisture content and temperature, humidity, wood species and wood density.

To help ensure your CUTEK® oil dries as quickly as possible, make sure you avoid:

  • Wet wood, or wood with a high moisture content. Your wood should contain a maximum moisture content of 17%, as anything higher can significantly delay the drying process. If this happens, CUTEK® oils may sit on the surface and eventually go tacky without penetrating properly.
  • Cold weather. In cold weather, CUTEK® oils will become thicker and therefore too much oil is applied. Warm oil by placing in a sunny/warm spot before application to make it thinner and enhance penetration.
  • Too many coats too soon. The first application of CUTEK® oil needs to completely diffuse and dry fully before the next coat is applied.
  • Existing oil, stain or paint on the surface. Existing film coats act as a barrier to a CUTEK® oil’s penetration. Old coatings must be fully removed by sanding and or chemical stripping prior to applying any CUTEK® exterior timber oil.

For best results, always allow CUTEK® oil to fully diffuse before recoating or use.  if you cannot wait, rag off the excess material on the surface and the coating will dry on top at a much faster rate.